-40%
HolyBro KakuteF7 HDV All-In-One Flight Controllers
HolyBro KakuteF7 HDV All-In-One Flight Controllers
HolyBro KakuteF7 HDV All-In-One Flight Controllers
HolyBro KakuteF7 HDV All-In-One Flight Controllers
HolyBro KakuteF7 HDV All-In-One Flight Controllers
HolyBro KakuteF7 HDV All-In-One Flight Controllers

HolyBro KakuteF7 HDV All-In-One Flight Controllers

$ 19.95

Availability: 100 in stock
  • Condition: New
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Item must be returned within: 30 Days
  • MPN: 11043
  • All returns accepted: Returns Accepted
  • Model: 11043
  • Restocking Fee: No
  • Brand: HolyBro
  • Return shipping will be paid by: Buyer

    Description

    HolyBro KakuteF7 HDV All-In-One Flight Controllers
    Overview Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIO to the DJI FPV VTx, for both signal and power supply. Features Supports Betaflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer. Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. 2 oz. copper PCB allows up to 120A maximum continuous current. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only). Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply. Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output up to 2A to DJI FPV VTx. Supports BLHeli pass-through for easy ESC upgrade and configuration. Specifications MCU: STM32F745 32-bit processor IMU:MPU6000 Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 6 hardware UARTS (UART1,2,3,4,6,7) All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”. Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. TF card for Blackbox logging Dimensions: 45x37mm Mounting Holes: Standard 30.5mm square to center of holes Weight: 10g Package Includes: FC board *1 M3 Damping Ball*4 JST GHR 8pin to JST GHR 6pin 80mm cable*1 Manual: Kakute F7 HDV AIO Manual More relevant product options https://shop.holybro.com/kakute-f7-hdv-aio-combo_p1193.html
    HolyBro KakuteF7 HDV All-In-One Flight Controllers
    Overview
    Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VT
    x
    module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIO to the DJI FPV VTx, for both signal and power supply.
    Features
    Supports Betaflight.
    High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
    Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
    Dedicated bootloader button for easy firmware flashing.
    Low-profile design fits into even very compact frames.
    2 oz. copper PCB allows up to 120A maximum continuous current.
    Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
    Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply.
    Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output up to 2A to DJI FPV VTx.
    Supports BLHeli pass-through for easy ESC upgrade and configuration.
    Specifications
    MCU: STM32F745 32-bit processor
    IMU:MPU6000
    Barometer: BMP280
    USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
    6 hardware UARTS (UART1,2,3,4,6,7)
    All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
    Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
    TF card for Blackbox logging
    Dimensions: 45x37mm
    Mounting Holes: Standard 30.5mm square to center of holes
    Weight: 10g
    Package Includes:
    FC board *1
    M3 Damping Ball*4
    JST GHR 8pin to JST GHR 6pin 80mm cable*1
    Manual:
    Kakute F7 HDV AIO Manual
    More relevant product options
    https://shop.holybro.com/kakute-f7-hdv-aio-combo_p1193.html
    ×
    ×
    ×
    ×
    ×
    ×
    ×
    Buy now and save!
    Tell a friend
    Visit store
    Watch now
    Postage info
    Click the Postage tab above the listing description for more info
    Click the Postage tab above the listing description for more info!
    Additional delivery notes
    PICK UP OPTION
    Sorry, our items are NOT available for pick-up.
    PAYING VIA PAYPAL
    We accept PayPal on our all our items so you can shop with confidence.
    Simple choose the PayPal option when proceeding through the checkout.
    Additional Information
    No additional information at this time
    Ask seller a question
    You might also like
    Align Torque Tube - Trex 500E Pro / 500 ESP / 500 EFL / 500 Pro DFC / 500L Domin
    Contact
    To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.
    Ask seller a question
    © HeliDirect
    Postage
    Click the Postage tab above the listing description for more info
    Payment
    Accepted Payment Methods
    PayPal
    Returns
    Returns are accepted
    Items must be returned within 30 days of the auction ending
    Buyer will pay for return shipping.
    eBay integration
    by