Matek System GNSS & Compass GPS M9N-5883 for Quad Drone Race Free Style NEW

Description

100% Original
Fair Pricing
Fast Shipping
BUY NOW!
Matek System GNSS & Compass GPS M9N-5883 for Quad Drone Race Free Style NEW
The Matek System M9N-5883 GNSS & Compass GPS uses multi-constellation GNSS powered by u-Blox NEO-M9N, and the NEO-M9N is a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou can be received concurrently.
Specifications
GNSS u-Blox NEO-M9N (GPS, GLONASS, Galileo, and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 25*25*4mm
Input voltage range: 4~6V (5V pad/pin)
Power consumption: 50mA
UART baud rate: 38400 default
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS NEO-M9N
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector
3.3V Power LED, Red
GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed
32mm*32mm*10mm
14.5g
Includes
1 x M9N-5883
1 x JST-GH-6P to JST-GH-6P 20cm silicon wire
Wiring and Settings
M9N-5883 5V to Flight controller 4~6V
M9N-5883 RX to Flight controller UART_TX
M9N-5883 TX to Flight controller UART_RX
M9N-5883 CL to Flight controller I2C_SCL
M9N-5883 DA to Flight controller I2C_SDA
M9N-5883 G to Flight controller GND
Compass Alignment(Arrow forward and flat mounting):
INAV/BetaFLight: CW 270° Flip when flight controller arrow is facing forward also.
Ardupilot/Mission Planner: Rotation None.
Protocol: Ublox or NEMA
Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron-based material
The scratches on the ceramic antenna are the result of tuning the antenna.
u-center Windows
TIps
NEO-M9N is supported by ArduPilot 4.1 (latest)
INAV2.5 ublox/ublox7/NEMA all don’t support NEO-M9N.
M9N is supported by INAV2.6 ublox or ublox7 protocol(both run at 5Hz)
Betaflight UBLOX protocol doesn’t support NEO-M9N,
Pls select
NEMA protocol
&
Auto Baud
.
HD cameras(Gopro, Split, Tarsier, etc) could interfere GPS signal, try turning off HD camera before GPS 3D fix
The NEO-M9N provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option.
Payment
Shipping
Returns
Secure & Easy Ordering. Orders can be placed online using PayPal to ensure a safe and secure transaction and guarantee you privacy. The address in Paypal is the address your order will be shipped to. We are only able to dispatch goods once payment has cleared. All refunds are issued via PayPal only.
Fast worldwide shipping with tracking number. We reserve the right not to ship to any unconfirmed PayPal addresses. Shipments usually takes 5-15 working days to your PayPal registered address.
ITALY, ISRAEL, SPAIN, GERMANY, EASTERN EUROPE, SOUTH AMERICA, AFRICA AND MIDDLE EAST may take from 10-25 days due the slow postal services and strict custom clearances.
After receiving the item, contact us within : 30 Days
Refund will be given as : Money back or item exchange (buyer's choice)
Return shipping : Buyer pays return shipping
100% Original
Fair Pricing
Fast Shipping
The Matek System M9N-5883 GNSS & Compass GPS uses multi-constellation GNSS powered by u-Blox NEO-M9N, and the NEO-M9N is a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou can be received concurrently. Specifications -------------- ---GNSS u-Blox NEO-M9N (GPS, GLONASS, Galileo, and BeiDou) ---Magnetic Compass QMC5883L ---Patch antenna 25*25*4mm ---Input voltage range: 4~6V (5V pad/pin) ---Power consumption: 50mA ---UART baud rate: 38400 default ---Operating Temperatures: -20~80 °C ---UART(TX, RX) interface for GNSS NEO-M9N ---I2C(DA, CL) interface for Compass QMC5883L ---JST-GH-6P connector ---3.3V Power LED, Red ---GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed ---32mm*32mm*10mm ---14.5g Includes -------- ---1 x M9N-5883 ---1 x JST-GH-6P to JST-GH-6P 20cm silicon wire Wiring and Settings ------------------- ---M9N-5883 5V to Flight controller 4~6V ---M9N-5883 RX to Flight controller UART_TX ---M9N-5883 TX to Flight controller UART_RX ---M9N-5883 CL to Flight controller I2C_SCL ---M9N-5883 DA to Flight controller I2C_SDA ---M9N-5883 G to Flight controller GND ---Compass Alignment(Arrow forward and flat mounting): ---INAV/BetaFLight: CW 270° Flip when flight controller arrow is facing forward also. ---Ardupilot/Mission Planner: Rotation None. ---Protocol: Ublox or NEMA ---Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron-based material ---The scratches on the ceramic antenna are the result of tuning the antenna. ---u-center Windows TIps ---- ---NEO-M9N is supported by ArduPilot 4.1 (latest) ---INAV2.5 ublox/ublox7/NEMA all don’t support NEO-M9N. M9N is supported by INAV2.6 ublox or ublox7 protocol(both run at 5Hz) ---Betaflight UBLOX protocol doesn’t support NEO-M9N, Pls select NEMA protocol & Auto Baud. ---HD cameras(Gopro, Split, Tarsier, etc) could interfere GPS signal, try turning off HD camera before GPS 3D fix ---The NEO-M9N provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. ![Matek System GNSS & Compass GPS M9N-5883] (https://cdn.shopify.com/s/files/1/0948/3076/files/M9N-5883_1.jpg?v=1611637526)![Matek System GNSS & Compass GPS M9N-5883] (https://cdn.shopify.com/s/files/1/0948/3076/files/M9N-5883_2.jpg?v=1611637546)![image] (https://cdn.shopify.com/s/files/1/0948/3076/files/M9N-5883_4.jpg?v=1611637567)
100% Original
BUY NOW!
Matek System GNSS & Compass GPS M9N-5883 for Quad Drone Race Free Style NEW
The Matek System M9N-5883 GNSS & Compass GPS uses multi-constellation GNSS powered by u-Blox NEO-M9N, and the NEO-M9N is a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou can be received concurrently.
Specifications
GNSS u-Blox NEO-M9N (GPS, GLONASS, Galileo, and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 25*25*4mm
Input voltage range: 4~6V (5V pad/pin)
Power consumption: 50mA
UART baud rate: 38400 default
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS NEO-M9N
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector
3.3V Power LED, Red
GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed
32mm*32mm*10mm
14.5g
Includes
1 x M9N-5883
1 x JST-GH-6P to JST-GH-6P 20cm silicon wire
Wiring and Settings
M9N-5883 5V to Flight controller 4~6V
M9N-5883 RX to Flight controller UART_TX
M9N-5883 TX to Flight controller UART_RX
M9N-5883 CL to Flight controller I2C_SCL
M9N-5883 DA to Flight controller I2C_SDA
M9N-5883 G to Flight controller GND
Compass Alignment(Arrow forward and flat mounting):
INAV/BetaFLight: CW 270° Flip when flight controller arrow is facing forward also.
Ardupilot/Mission Planner: Rotation None.
Protocol: Ublox or NEMA
Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron-based material
The scratches on the ceramic antenna are the result of tuning the antenna.
u-center Windows
TIps
NEO-M9N is supported by ArduPilot 4.1 (latest)
INAV2.5 ublox/ublox7/NEMA all don’t support NEO-M9N.
M9N is supported by INAV2.6 ublox or ublox7 protocol(both run at 5Hz)
Betaflight UBLOX protocol doesn’t support NEO-M9N,
Pls select
NEMA protocol
&
Auto Baud
.
HD cameras(Gopro, Split, Tarsier, etc) could interfere GPS signal, try turning off HD camera before GPS 3D fix
The NEO-M9N provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option.
Payment
Secure & Easy Ordering. Orders can be placed online using PayPal to ensure a safe and secure transaction and guarantee you privacy. The address in Paypal is the address your order will be shipped to. We are only able to dispatch goods once payment has cleared. All refunds are issued via PayPal only.
Shipping
Fast worldwide shipping with tracking number. We reserve the right not to ship to any unconfirmed PayPal addresses. Shipments usually takes 5-15 working days to your PayPal registered address.
ITALY, ISRAEL, SPAIN, GERMANY, EASTERN EUROPE, SOUTH AMERICA, AFRICA AND MIDDLE EAST may take from 10-25 days due the slow postal services and strict custom clearances.
Returns
After receiving the item, contact us within : 30 Days
Refund will be given as : Money back or item exchange (buyer's choice)
Return shipping : Buyer pays return shipping
100% Original
Fast Shipping
Fair Pricing
The Matek System M9N-5883 GNSS & Compass GPS uses multi-constellation GNSS powered by u-Blox NEO-M9N, and the NEO-M9N is a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou can be received concurrently.
Specifications
GNSS u-Blox NEO-M9N (GPS, GLONASS, Galileo, and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 25*25*4mm
Input voltage range: 4~6V (5V pad/pin)
Power consumption: 50mA
UART baud rate: 38400 default
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS NEO-M9N
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector
3.3V Power LED, Red
GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed
32mm*32mm*10mm
14.5g
Includes
1 x M9N-5883
1 x JST-GH-6P to JST-GH-6P 20cm silicon wire
Wiring and Settings
M9N-5883 5V to Flight controller 4~6V
M9N-5883 RX to Flight controller UART_TX
M9N-5883 TX to Flight controller UART_RX
M9N-5883 CL to Flight controller I2C_SCL
M9N-5883 DA to Flight controller I2C_SDA
M9N-5883 G to Flight controller GND
Compass Alignment(Arrow forward and flat mounting):
INAV/BetaFLight: CW 270° Flip when flight controller arrow is facing forward also.
Ardupilot/Mission Planner: Rotation None.
Protocol: Ublox or NEMA
Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron-based material
The scratches on the ceramic antenna are the result of tuning the antenna.
u-center Windows
TIps
NEO-M9N is supported by ArduPilot 4.1 (latest)
INAV2.5 ublox/ublox7/NEMA all don’t support NEO-M9N.
M9N is supported by INAV2.6 ublox or ublox7 protocol(both run at 5Hz)
Betaflight UBLOX protocol doesn’t support NEO-M9N,
Pls select
NEMA protocol
&
Auto Baud
.
HD cameras(Gopro, Split, Tarsier, etc) could interfere GPS signal, try turning off HD camera before GPS 3D fix
The NEO-M9N provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option.