Pixhawk 4 Mini +GPS +PM06 V2 Flight Controller GPS Power Management Board 120A

Description

Description
Pixhawk 4 Mini & GPS & PM06 V2 Version Flight Controller with GPS Power Management Board Package 1
Pixhawk 4 Mini
The Pixhawk 4 Mini autopilot is designed for engineers and hobbyists who are looking to tap into the power of Pixhawk 4 but are working with smaller drones. Pixhawk 4 Mini takes the FMU processor and memory resources from the Pixhawk 4 while eliminating interfaces that are normally unused. This allows the Pixhawk 4 Mini to be small enough to fit in a 250mm racer drone.
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
Pixhawk4 mini firmware version: 1.8.0 dev
Quick Summary:
☆Main FMU Processor: STM32F765
- 32 Bit ArmCortex-M7, 216MHz, 2MB memory, 512KB RAM
☆On-board sensors:
- Accel/Gyro: ICM-20689
- Accel/Gyro: BMI055
- Magnetometer: IST8310
- Barometer: MS5611
☆GPS: ublox Neo-M8N GPS/GLONASS receiver; integrated magnetometer IST8310
☆Interfaces:
- 8 PWM outputs
- 4 dedicated PWM/grabbing inputs on FMU
- Dedicated R/C input for CPPM
- Dedicated R/C input for Spektrum / DSM and S.Bus with analog / PWM RSSI input
- 3 general purpose serial ports
- 2 I2C ports
- 3 SPI buses
- 1 CANBuses for CAN ESC
- Analog inputs for voltage / current of battery
- 2 additional analog input
☆Power System:
- Power Brick Input: 4.75~5.5V
- USB Power Input: 4.75~5.25V
- Servo Rail Input: 0~24V
- Max current sensing: 120A
☆Weight and Dimensions:
- Dimensions: 38x55x15.5mm
☆Other Characteristics:
- Operating temperature: -40 ~ 85℃
Package 1:
Pixhawk4 mini *1
Pixhawk4 GPS MODULE *1
PM06 V2 Power Management Board *1
I2C splitter Board *1
6 to 6 pin cable (power) *1
4 to 4 pin cable (CAN) *1
6 to 4 pin cable (Data) *1
6 to 4 pin and 4 pin "Y"cable *1
6 to 6 pin cable(Debug) *1
PPM/SBUS out cable *1
XSR receiver cable *1
DSMX receiver cable *1
SBUS receiver cable *1
USB cable *1
'X'type folding pedestal mount *1
70mm & 140mm carbon rod stand off *2
Foam Set *1
Pixhawk4 mini Quick Start Guide *1
Package 2:
Pixhawk4 mini *1
PM06 V2 Power Management Board *1
I2C splitter Board *1
6 to 6 pin cable (power) *1
4 to 4 pin cable (CAN) *1
6 to 4 pin cable (Data) *1
6 to 4 pin and 4 pin "Y"cable *1
6 to 6 pin cable(Debug) *1
PPM/SBUS out cable *1
XSR receiver cable *1
DSMX receiver cable *1
SBUS receiver cable *1
USB cable *1
Foam Set *1
Pixhawk4 mini Quick Start Guide *1
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.